yield strength

Temperature dependence of fracture toughness or yield strength of low carbon steel

低碳钢的断裂韧性和屈服强度的低温温度依赖性

The pipeline steel with strain-based design is usually characterized by high initial work hardening rate, good ductility, and low yield stress to tensile strength ratio.

抗大变形管线钢就是基于应变设计的方法得到的具有连续屈服、较低的屈强比、较高的加工硬化指数以及均匀塑性变形延伸率等特性的管线钢。

Research on Improving High Strength Steel's Yield Strength

提高冷轧高强度钢板屈服强度控制水平的研究

Pore size had low effect to yield strength.

孔径对屈服应力的影响不大。

The yield strength and elastic modulus will decrease with the temperature increased.

温度升高，原子热运动加强，屈服强度和弹性模量降低。

The yield strength fy of reinforcement is used in design.

在设计中利用的是钢筋的屈服强度.

The V-N microalloy steel with yield strength of 550 MPa is produced by EAF-CSP route.

目前,在EAF-CSP 流程中通过V -N 微合金化技术可成功生产屈服强度为550MPa的高强度低合金钢.

Quenching and tempering heat treatment are integrated in order to improve the mechanical properties of fasteners to meet the product requirements of tensile strength and yield ratio value.

热处理调质是为了提高紧固件的综合力学性能，满足产品规定的抗拉强度值和屈强比。

Experimental research and prediction of yield strength for aging strengthened aluminium alloy

铝合金时效强化的实验研究及屈服强度计算

An improved method for measuring the unconfined yield strength of powders against negative pressure drop

负压差散体颗粒无约束屈服强度实验测量方法

Calculation of the Yield Strength in Non-quenched-tempered Steel

连铸连轧非调质钢屈服强度的计算

Application of SAS tools to increasing yield strength of grade CQ

SAS在优化CQ级屈服点研究中的应用

Effect of Different Vanadium Microalloying Addition on the Ratio of Tensile Strength and Yield Strength

不同钒微合金化方式对钢筋强屈比的影响

Desirable properties for forming include low yield strength and high ductility.

令人满意的成形特性包含了低降伏应力和高延展性.

Oxgen precipitates ( useful for gettering ) can reduce the yield strength ( critical shear stress ) up to fivefole.

氧沉淀 ( 可用作吸杂 ) 会使屈服强度 ( 临界剪应力 ) 降低为五分之一.

CuPTiRE anti-erosion hot rolling stripes are divided into two grades in yield strength : 295 MPa, 345 MPa.

09CuPTiRE耐大气腐蚀热轧钢板按屈服强度分为295MPa级和345MPa级两个级别.

Yield Strength of Shot Peened Surface of a Metallic Material in Hard State

硬状态材料喷丸表面的屈服强度

But for the die-cast Mg-Al-Nd magnesium alloy, when the holding time of solution treatment was same, the ultimate tensile and elongation of alloys would increase while the yield strength of alloy could be decreased with the solution treatment temperature heighten.

对于压铸态Mg-Al-Nd镁合金，当固溶处理后保温时间相同，随着固溶温度的升高，合金的抗拉强度和伸长率升高，但是屈服强度却降低了。

The creep rate was increased while the yield strength was reduced by anodic dissolution.

阳极电流不但使恒载荷下的不锈钢蠕变速度增加,而且使屈服强度下降.

The yield strength measurement of LY-12 aluminium alloy under high temperature

LY&12铝高温屈服强度的测量

Residual stress concentration a notch depends on both notch geometry and yield strength of the material.

缺口根部的残余应力存在应力集中效应,应力集中值不仅取决于缺口几何形状而且和材料的屈服强度有关.

The yield strength, tensile ratio and toughness are major quality indexes of steel pipe ( board ).

屈服强度 、 屈强比、韧性等是钢管 ( 板 ) 的主要质量指标,合理确定这些指标的数值有相当难度.

FIG. 5 shows the average yield strength as a function of extrusion speed and location.

图5示出了平均屈服强度与挤压速度和位置的关系.

Study on Increasing the Yield Strength of Autobody Resistance Welding Electrode

提高汽车车身电阻焊电极屈服强度的研究

The Applications of Computer To Testing Material's Conditional Yield Strength

计算机在测定村料条件屈服强度中的应用

A model for the yield strength of a thin polycrystalline film

多晶薄膜屈服强度的一个模型

The results show that the steel has high yield strength and quality forming property.

结果表明,研制开发出的铌钛微合金化IF钢具有高的屈服强度和优良的成形性能.

Compared with neat PA6, the tensile modulus, the yield strength and the hardness of the nanocomposites were improved by about 100% 75%, and 25%, respectively, with incorporation of only 1 wt% CoAl-LDH.

当仅加入1wt%LDH时，尼龙6纳米复合材料的弹性模量、屈服强度和硬度比纯尼龙6分别提高了100%、75%和25%。

Dislocation strengthening and grain refinement strengthening makes coil 059 with the higher yield strength.

位错强化与晶粒细化强化是059板卷具有高屈服强度的原因.

The yield strength ( σ0.2 ) , ultimate tensile strength ( σ b ) and elongation ( δ ) of A 356-T 6 alloy were 240 MPa, 254.8 MPa and 1.16 % , respectively.

屈服强度 、 抗拉强度和伸长率分别为240MPa 、 254.8MPa和1.16%.