optimization design

A Discrete Optimization Design Method for Less-Curved Surface Gird With With Minimum Cost

微曲面网架最小造价的离散优化设计

Fuzzy Optimization Design for the V-belt Transmission of Low-profile Crusher Based on Matlab

基于Matlab的低矮式破碎机V带传动模糊优化设计

Component Granularity Optimization Design Based on Business Model Stability Evaluation

基于业务模型稳定性的构件粒度优化设计

Study of reloading optimization design for nuclear heating reactors

核供热堆换料优化设计研究

Dynamic Simulation of Long Jump and Optimization Design of Takeoff Parameters

跳远动力学仿真与踏跳参数的最优化设计

Optimization Design and Simulation of the Floor Plate Structure Used in A Railway Passenger Train Based on Genetic Algorithm

基于遗传算法的铁路客车地板结构优化设计与仿真

Therefore, the aim of the research of queue theory is that how to achieve its optimization design and control through research of laws of probability, consequently, to realize the whole system bring into play its maximal benefit with the least cost.

而排队论的研究目的是通过对排队系统中概率规律的研究，使系统达到最优设计和最优控制，以最小费用实现系统的最大效益。

Application of equivalent round disk theory to optimization design on scoops of gas centrifuge

等效圆盘理论在气体离心机取料器优化设计上的应用

Mutil objective Optimization Design for the Three Gorges Dam Monitoring Network

三峡坝区变形监测网多目标优化研究

Optimization Design for Toggle Clamping System of Injection Moulding Machine

注射机曲肘式合模机构的最优化设计

Based on the dynamic simulation of the spindle system of 5-axis machining center, dynamic optimization design is done for the bearing support system and the structure of the spindle.

对五轴联动加工中心主轴系统进行动力学仿真分析，对原主轴系统的轴承支承系统和主轴结构进行了动态优化设计，提出了双排轴承的设计方案。

The Optimization Design of the Chain Hinge Wear Testing Machine

链条铰链磨损试验机的优化设计

The optimal composition and heat treatment conditions were obtained by optimization design and Verification test.

通过优化设计和验证实验确定了一组耐腐蚀性能最佳的成分组合和热处理参数。

Optimization design of main parameters for the boom of drilling jumbo

凿岩台车支臂主参数的优化设计

A method of topological optimization design for the truss structures under multiple loading conditions

一种多工况下桁架结构的拓扑优化设计方法

Different from the general topology optimization design, both the optimal topology and the optimal shape and size can be obtained.

这类问题不同于一般意义的拓扑优化问题，其优化结果不仅得到最优拓扑，而且得到最优形状和尺寸。

An optimization design method for bending rigidity of main shaft for large wind turbines

大型风力机主轴最佳抗弯刚度的设计方法

Using homogenization method, an optimization design method of compliant mechanisms is studied.

应用均匀化方法，探讨以机械效率为优化目标的柔顺机构的设计方法。

Optimization Design with CAE for Precision Injection Mould for Solder Wire Plates

精密焊丝盘注塑模具的CAE优化设计

Aiming at the reliability problems in the elevation-balancing machine, traversing machine and self-filling equipment, this paper completes the parameter optimization design and simulation research for movement reliability.

针对高低平衡机、方向机和自动装填机构的可靠性问题，进行了动作可靠性参数优化设计与仿真研究。

Optimization Design of Roll Series for HC Mill

HC轧机辊系优化设计

Optimization design of hydraulic wrench based on 3D nonlinear finite element

基于三维非线性有限元的液压扳手的优化改进设计

Optimization design of a new type spiral wedge hydrodynamic bearing

螺旋油楔动压轴承的优化设计

Optimization Design of 15 Kilowatt Columnar Push-pull Magnetic Driver

15千瓦圆筒形推拉式磁驱动器的优化设计

Optimization design of reliability of automobile front-axle

汽车前轴的可靠性优化设计

Optimization Design in Electrochemistry Rectifying Supply ICAD

电化学整流电源ICAD的优化设计

The algorithm optimization design of MP3 encoding based on fixed-point DSP

一种在定点DSP上实现MP3实时编码的算法优化设计

Discussion to Optimization Design for Structure of Vibrating Chute Equipment

振动放矿设备结构优化设计探讨

Optimization Design for Parameters of Optical Four-Quad Splitter

光学四象限分光器参数的优化设计

Optimization Design of Engine Piston Profile Basing on Glide Software

基于GLIDE软件的发动机活塞型线设计优化