meshing

Fully automatic meshing, with optional fine-grained user control for specific components.

全自动啮合, 可选细粒度的用户控制,为具体的组成部分.

Because of the meshing stiffness of a gear pair, the governing equation denotes a linear dynamic system with periodic time-varying coefficient.

由于齿轮副啮合刚度的影响，动力学方程式代表了一个具有时变系数的线性动力系统。

On radiosity meshing Parameters, enabled Global Subdivision Settings.

论辐射啮合参数, 使全球细分设置.

Meshing gears must have the same pressure angles.

互相啮合的齿轮具有相同的压力角.

Influence of Speed Ratio on Rattling Threshold Speed of a Gear System with Time-Varying Meshing Stiffness

传动比对齿轮时变系统拍击门槛转速的影响

Determination of Meshing Parameter of Pinion Machine Tool in Cutting Bevel Gear Transmission

切制锥齿轮传动的小齿轮时机床啮合参数的确定

A brick element re-meshing technique was presented for shape-metal rolling process.

摘要提出了一种适用于型钢轧制及其类似过程的六面体网格重构方法.

Meshing Theory and Application Study of Grinding Gear with the Toroidal Involute Interior Thread Worm Grind Wheel

TI内螺纹蜗杆砂轮磨齿的啮合理论及应用研究

Worn gear wheel and deep meshing of gears.

齿轮磨灭和齿轮啮合不当.

Installation error will cause the bevel gear meshing error in low-load or overload conditions, the actual contact length is less than or greater than the theoretical contact length.

安装误差会引起锥齿轮副啮合误差，在低载或重载条件下，实际接触长度小于或大于理论接触长度。

A principle of self-position meshing track for conveyer chain has been proposed.

提出了跟踪运输链节的“滚动啮合自位跟踪”原理.

Transitional-zone method in hexahedral finite element meshing in geotechnical engineering

岩土工程数值分析中的过渡区方法

Meshing to minish analysis error is a concerned problem in FEA.

如何划分网格以减小分析误差是有限元分析中令人关心的问题.

Meshing the research and marketing operations will be Mr. Furlaud's job.

把研究与市场运作紧密结合起来将成为弗劳德先生的工作任务。

Exact modeling of gear teeth is based on meshing theory.

摘要根据齿轮啮合原理,建立了轮齿的精确齿形.

Meshing and Remeshing Techniques for Hexahedral Mesh in the Finite Element Simulation of Plastic Forming

塑性成形有限元模拟六面体网格划分和再划分技术

Meshing characteristic and helix error rule of small pressure angle worm

小齿形角蜗杆的啮合特性与螺旋线误差规律

Specifies meshing parameters for automatic ( smart ) element sizing .

为自动 单元划分 指定分网参数.

There were some beautiful harmonies meshing behind the dreamy bass line.

有在梦幻的低音线后面以网捕捉的一些美丽的协调.

The time-variant meshing stiffness also causes large dynamic load in gear pairs.

时变啮合刚度还导致了较大的动载荷；

Meshing method is one of the key factors of meshing direction feature.

网格技术是网格方向特征的关键技术之一.

Spiral bevel gear is a common room meshing gear.

螺旋锥齿轮，又称螺伞锥齿轮，是一种常见空间啮合齿轮。

Meshing spur gears must have the same diametral pitch.

互相啮合的直齿圆柱齿轮,必须具有相同的径节.

A-operator method ( AOM) is used to study the influence of the torque fluctuation and time-varying meshing stiffness on rattling threshold speed of the gear system.

用算符分解算法（AOM）研究了扭矩波动和时变啮合刚度对拍击门槛转速的影响。

In this article the bearing ability test of hard gear face point-line meshing gear transmission and the trial of noise test are introduced.

本文介绍了硬齿面点线啮合齿轮传动的承载能力试验和噪声测定试验的情况。

These formulae are suitable for any contacting point of tooth surface meshing.

这些公式适用于齿面啮合的任何接触点.

The causes of phase variation in air supply obtained after analysis are mainly errors in manufacture, abuse in operation and errors in repair. Several adjusting methods for correct installation of timing gears, inspection of meshing clearance of gear faces and adjustment of valve clearance are suggested.

分析了配气相位变化的原因主要是制造误差、使用不当和修配误差等，提出了正确安装正时齿轮、检查齿面啮合间隙和调整气门脚间隙等几种调整方法。

The modification of gear is a principal method for improving performance meshing.

齿面修形是提高齿轮副啮合性能的重要手段.

The Influence of Meshing Density on Automobile Crashing Simulation and the Efficiency of Calculation

网络密度对车辆碰撞仿真的影响与计算效率

Based on the meshing and geometry relationship between the profiles.

以复数矢量法建立了直线共轭齿廓的啮合线方程.