insertion loss

Insertion Loss . The attenuation of signals being routed through a switching card.

插入损耗被路由信号通过开关卡的衰减.

Theoretically: Connector, balun insertion loss and amplifier gain are not included.

理论: 不含接头 、 平衡非平衡转换器损失、放大器增益.

Feature: Excellent insertion loss and return loss, Frequency response width, Low loss.

特点: 具有极佳的插入损耗和回波损耗, 频率响应宽, 损耗低等特点.

Low-insertion loss, high return loss and high slope selectivity are simultaneously required for filters.

滤波器要求同时满足低插入损耗 、 高回波损耗和高频率选择斜率性能要求.

High-Q tuned LC filters will have more insertion loss.

高Q值调谐LC滤波器会有更多的插入损耗.

The test results showed the predicted insertion loss agreed well with the measured value.

试验结果表明,插入损失的预估值与实测值相符.

They have high reflection losses and isolates degree, lower insertion loss.

具有高的反射损耗和隔离度, 较低的插入损耗.

Take an example, the insertion loss of simple expansion chamber muffler has been calculated.

作为应用实例，文中对简单膨胀腔消声器的插入损失进行了计算。

High temperature superconductors microwave devices provide the advantages of lower insertion loss and lower noise figure.

高温超导微波器件具有极低损耗和极低噪声的优良特性.

An ultra low insertion loss GaAs MMIC RF SPDT switch based on full-ion-implantation technology is reported.

报道了利用离子注入技术研制出一种用于手机的超低插损砷化镓单片射频单刀双掷开关.

Method of insertion loss measurement for radio frequency filters.

射频滤波器插入损耗的测量方法.

This method can not only estimate efficiently the noise barrier insertion loss but also optimize the incline angle parameters in accordance with the actual requirements. It provides an effective design basis for applied engineering.

该方法不但可以方便地预估出声屏障的插入损失，而且可以根据实际要求对声屏障折壁角的参数进行优化设计，为工程应用提供一种有效的设计依据。

A kind of silicon micromachine F-P cavity variable attenuator is introduced. Basic structure and basic principle is described. It has advantages of minuteness volume, low insertion loss, high adjustment precision.

一种新型的硅微机械FP腔可变衰减器，具有体积小、插入损耗低、调节精度高等优点，介绍了其基本结构、基本原理。

Due to the frequency selectivity and high insertion loss of SAW device, the input must be high pulse whose spectrum width can cover the center frequency of SAW tap delay line.

由于SAW器件具有频率选择性及较高的插入损耗，使得它的输入必须为高脉冲且脉冲的频谱宽度能覆盖SAW抽头延迟线的中心频率。

When calculating insertion loss by BEM, materials of barrier, shape of barrier and ground surface type can be involved.

边界元法计算插入损失时可以考虑声屏障各部分具体材料、形状及地面类型。

Some of these considderationsinclude insertion loss, cross talk, propagation delay , and unterminated stubs.

需要考虑的因素包括插入损耗 、 串扰 、 传输延迟和未端接短截线.

Due to insertion loss, the signal may require amplification.

由于存在插入损耗, 所以信号可能需要放大.

Specialties: Small Dimension , Low Insertion Loss , High Restraint Outside the Band and High Reliability.

特点: 可实现的滤波器的体积小, 插入损耗小, 还外抑制高,可靠性高.

Practically: Including connector, balun insertion loss and amplifier gain.

实际: 包含接头 、 平衡非平衡转换器损失、放大器增益.

Therefore, they exhibit lower insertion loss and are much shorter than the conventional designs.

因此, 它具有比传统设计更低的插入损耗和更短的结构.